Amcor air conditioner troubleshooting

Your air conditioner broke down or works incorrectly? Before any repair work, you should diagnose and identify the cause of the problem. This table will help you get rid of erroneous conclusions and let you restore the device faster.

Amcor AF 8000E air conditioner troubleshooting

ProblemCauseSolution
The air conditioner does not function.No power supply.Connect to a functioning outlet and switch on.
Is the power light flashing?Empty the drain pan.
Timer function is active.Deactivate the TIMER function.
The air conditioner does not seem to perform.The unit is in direct sunlight.Close curtains.
Windows or doors open, many people or a heat source in the room.Close doors and windows, place an extra air conditioner.
The filter is dirty.Clean or replace the filter.
Air inlet or air outlet blocked.Remove the blockage.
Room temperature lower than the selected value.Change temperature selection. Set at the lowest possible setting: 17 °C.
The unit is noisy.Unit stands uneven.Place on an even, solid surface (less vibrations).
The compressor does not work.The overheat protection is probably activated.Wait 3 minutes until the temperature has decreased, then turn on the unit again.
The remote control does not function.Distance too great.Make sure the remote control is correctly aimed at the control panel.
Remote control signal not detected by the control panel.
The batteries are drained.Replace the batteries.

Amcor AMC 10KM-410 air conditioner troubleshooting

ProblemCauseSolution
The unit does not functionCheck the plug fuse. Check the mains outlet by connecting another applianceConnect to a functioning outlet and switch on
Water container indicator is onEmpty water container
Room temperature outside operating temperature range
The unit does not seem to performIn direct sunlightClose curtains
Windows or doors open, many people or heat source in room
Dirty filterClean or replace filter
Air inlet or air outlet blockedRemove blockage
Room temperature lower than selected valueChange temperature selection
The unit is noisyUnit stands unevenPlace on even surface (less vibrations)
The compressor does not workOverheat protection probably activatedWait until room temperature lowers

Amcor CPLMB-12000E air conditioner troubleshooting

ProblemCauseSolution
The Air Condi- tioner Does Not Function ProperlyWindows or doors are open.Close doors and windows.
The filter is dirty.Clean or replace filter.
Air inlet or air outlet is blocked.Remove blockage.
Room temperature lower than the selected value.Lower temperature selected.
The Unit Does NothingThe overheat protection is activated.Wait 3 minutes until temperature has decreased, then turn on again.
No power supply.Make sure outlet works.
Be sure Green Light is on (L.C.D.I. Plug) Press Re-start button.
Water container is full. The LCD light is flashingDrain the Unit.
Timer Function Set.Deactivate the Timer Function.
The Unit is NoisyUnit is not standing on a level surface.Place on an even surface.
The Remote Control Does Not FunctionDistance too great.Make sure the remote is aimed at the control panel.
Remote control signal not detected by control panel.Control is aimed at the control panel.
Batteries are dead.Replace the batteries.

Amcor NanoMax A12000EH air conditioner troubleshooting

ProblemCauseSolution
The air conditioner does not functionNo power supply. Make sure the green light on the plug is lit.Connect to a functioning outlet and switch on.
Is the power light flashing? Is the water full LED lit?Empty the drain pan.
The air conditioner does not seem to perform.The unit is in direct sunlight.Close curtains.
Windows or doors open, many people or a heat source in the room.Close doors and windows, place an extra air conditioner.
The filter is dirty.Clean or replace the filter.
Air inlet or air outlet blocked.Remove the blockage.
Room temperature lower than the selected value.Change temperature selection.
Set at the lowest possible setting: 62°F.
The unit is noisy.Unit stands uneven.Place on an even, solid surface (less vibrations).
The compressor does not work.The overheat protection may be activated.Wait 30 minutes until the temperature has decreased, then turn on the unit again.
The remote control does not function.Distance too great.Make sure the remote control is correctly aimed at the control panel.
Remote control signal not detected by the control panel.
The batteries are drained.Replace the batteries.